Step by Step Configuration of NTP Server on HP-UX Server

In this post, I would like to explain how we configure the NTP (network time protocol) server on HP-UX operating system server. In my recent post you can found the NTP configuration on Solaris and AIX platform. 

As you know NTP ( Network time Protocol) is one of the oldest internet protocol still in use and it allows the synchronization of computer clocks distributing UTC (Coordinated Universal Time) over the network. It is basaiclly used for time synchronization on Unix servers.

Step by Step Configuration of NTP Server on HP-UX:

➤ In the first step we will check the configuration files of "xntpd" daemon. By default the configuration file for this daemon is "/etc/rc.config.d/netdaemons".

hpx:/> vi /etc/rc.config.d/netdaemons

######################################

# xntp configuration.  See xntpd(1m) #

######################################

#

#  Time synchronization daemon

#

# NTPDATE_SERVER: name of trusted timeserver to synchronize with at boot

# (default is rootserver for diskess clients)

# XNTPD:        Set to 1 to start xntpd (0 to not run xntpd)

# XNTPD_ARGS:  command line arguments for xntpd

#

# Also, see the /etc/ntp.conf and /etc/ntp.keys file for additional

# configuration.

#

export NTPDATE_SERVER=

export XNTPD=0

export XNTPD_ARGS=

This is default configuration entry of this file so for xntpd daemon we need to change the variable which is defined.

export NTPDATE_SERVER='ntp.in.pool.org'

export XNTPD=1

export XNTPD_ARGS=

Note: You must change the NTPDATE server name.

➤ For ntp config please set the correct timezone is setup in /etc/TIMEZONE file.

hpx:/> cat /etc/TIMEZONE

TZ=IST-5:30

export TZ

You can edit the file in vi editor and change the time zone as per your location.

➤ Now, we need to make some changes in NTP configuration files. 

hpx:/> cat /etc/ntp.conf

#Configuration NTP des serveurs

server ntp.in.org.com

server ntpin.in.org.com

You need to replace ntp server name accordingly. In my post I will use dummy server name.

➤ After setting the NTP server name we need to restart the NTP service on HP-UX operating system and verify the ntp configuration.

hpx:/> /sbin/init.d/xntpd restart

hpx:/> ntpq -p

If it is showing you correct ntp server information now. You can match these information with the NTP server name which we use in above step.

HP-UX Logical Volume Manager (LVM) Commands with an Example

In this post, You can get an idea about HP-UX logical volume manager commands with an example. As you know LVM is basically used for disk management in operating system that allow to manager the physical disks and logical volume.

Please find the below HP-UX LVM commands with an example.

➤ Create a new volume group, logical volume and file system:

You can used the below command in HP-UX operating system to create a new volume group, logical volume and file system.

hpx:/>pvcreate /dev/rdsk/c2t1d0

For creating a new volume group first we need to create physical volume as describe in above command.

hpx:/>mkdir /dev/vg01

hpx:/>mknod /dev/vg01/group c 64 0x010000

In above step we will create a directory where we need to create a volume group.

hpx:/>vgcreate /dev/vg01 /dev/dsk/c2t1d0

After successfully creation of volume group we will create a new logical voulme as describe in below command.

hpx:/>lvcreate -L 2048 /dev/vg01

hpx:/>newfs -F vxfs -o largefiles /dev/vg01/vgvol1

Using above command we create a new file system now in next step we will create a directory where we need to mount the newly created file system.

hpx:/>mkdir /backup

hpx:/>mount /dev/vg01/vgvol1 /backup

Once you mount the logical voulme with file system you can run the file system checking command to verify that mounting is succesfully or not.

➤ Create a stripped filesystem:

In this, we will create a stripped file system with the help of volume group and logical voulme.

hpx:/>lvcreate -i 2 -I 32 -L 48 -n vgvol1 /dev/vg01

-i number of stripes

-I stripe size of 32KB

-L size of the volume

➤ HP-UX display boot information:

You can use the below command to display boot information.

hpx:/>lvlnboot -v /dev/vg00

Boot Definitions for Volume Group /dev/vg00:

Physical Volumes belonging in Root Volume Group:

        /dev/dsk/c2t0d0 (0/1/1/0.0.0) -- Boot Disk

        /dev/dsk/c2t1d0 (0/1/1/0.1.0) -- Boot Disk

Boot: lvol1     on:     /dev/dsk/c2t0d0

                        /dev/dsk/c2t1d0

Root: lvol3     on:     /dev/dsk/c2t0d0

                        /dev/dsk/c2t1d0

Swap: lvol2     on:     /dev/dsk/c2t0d0

                        /dev/dsk/c2t1d0

Dump: lvol2     on:     /dev/dsk/c2t0d0, 0

When you run the above command you can find the above output , if you see the boot information you can find you have two disk which is available for boot.

➤ HP-UX display all disks system information:

hpx:/> ioscan -funC disk

Class     I  H/W Path        Driver   S/W State   H/W Type     Description

==============================================================

disk      0  0/0/2/0.0.0.0   sdisk    CLAIMED     DEVICE       TEAC    DV-28E-N

                            /dev/dsk/c0t0d0   /dev/rdsk/c0t0d0

disk      1  0/1/1/0.0.0     sdisk    CLAIMED     DEVICE       HP 146 GMAX3147NC

                            /dev/dsk/c2t0d0   /dev/rdsk/c2t0d0

disk      2  0/1/1/0.1.0     sdisk    CLAIMED     DEVICE       HP 146 GMAX3147NC

                            /dev/dsk/c2t1d0   /dev/rdsk/c2t1d0

In the above output you can found the all the disk which is available in the system.

➤ HP-UX display dump devices:

hpx:/> lvlnboot -v

Normally it is showing the boot information in which you can check the dump devices name.

How to find the boot disk from HP-UX operating system

In this article , I would explain to you how we find which disk are used to boot the running HP-UX operating system. This is a bit tricky because its depending on the version of HP-UX, and whether it is using LVM or the less common choice.

For LVM disk layouts:

For 11.11 and earlier, use the below command to check which disk is in used.

hpx:/> echo “boot_string/S” | adb -k /stand/vmunix /dev/kmem

    boot_string:

    boot_string:    disk(0/0/2/0.6.0.0.0.0.0;0)/stand/vmunix

For 11.23, there are different ways for PARISC versus IA64:

PARISC:

hpx:/> echo “boot_string/S” | adb -o /stand/vmunix /dev/kmem

    boot_string:

    boot_string:    disk(1/0/0/3/0.6.0.0.0.0.0;0)/stand/vmunix

IA64 (Itanium/Integrity):

hpx:/> echo “bootdev/x” | adb -n /stand/vmunix /dev/kmem

    bootdev:

        0x100001c

Now to find the actual path, you’ll have to match the 0x100001c value to a minor number in the /dev/disk directory. Compare only the last 6 digits of the number (00001c) to find the device file. Then by using lssf, you can decode the hardware path:

    hpx:/> DSK=$(ll /dev/disk | awk ‘/00001c/{print $NF}’)

    hpx:/> echo $DSK

    disk11_p2

    hpx:/> HWPATH=$(lssf /dev/disk/$DSK | awk ‘{print $(NF-1)}’)

    hpx:/> echo “$DSK path = $HWPATH”

    disk11_p2 path = 64000/0xfa00/0xa

You can also use ioscan -m dsf to map agile device file names to legacy (CTD) style.

For VxVM disk layouts:

hpx:/> echo “raw_root/X” | adb -o /stand/vmunix /dev/kmem

     raw_root:

     raw_root:       0x3000002

This value is the minor number for the disk that was used to boot the current system. The minor number is found in the /dev/vx/dmp directory.

     hpx:/> DSK=$(ll /dev/vx/dmp | awk ‘/000002/{print $NF}’)

     hpx:/> echo $DSK

    c2t1d0s2

     hpx:/> HWPATH=$(lssf /dev/dsk/$DSK | awk ‘{print $(NF-1)}’)

     hpx:/> echo “$DSK path = $HWPATH”

     c2t1d0s2 path = 0/1/1/0.1.0

For completeness, I should mention that 11.31 will report the boot disk path in syslog.log (LVM or VxVM) like this:

vmunix: Boot device’s HP-UX HW path is: 0/1/1/0.0×1.0x0

However, syslog.log is a catch-all for a lot of items and often needs to be truncated when it grows too large. As a result, it can’t be relied on to always contain the current boot disk.